Features
- 400 to 2,200 CFM
- High-static ducted vertical fan coil, manufactured of heavy-gauge galvanized steel and insulated with 1/2" thick, over three-pound density, neoprene-coated fiberglass; insulated drain pan with primary and secondary drain connections constructed of galvanized metal and finished with a powder-coated epoxy, easily removable motor/blower assembly with quick-connect plug
- Top-supply with front return
- Primarily used in vertical floor-mounted or hideaway applications the unit is furred into partition walls or hidden in closets, utility rooms and other concealed locations with a ducted discharge
- Removable front panel for easy maintenance
- One-inch discharge duct flange is standard on the top panel
- Coils are manufactured of copper tube with aluminum fins and are 100% underwater pressure tested to 350 PSI with a 300 PSI working pressure
- Galvanized drain pan is finished with a powder-coated epoxy, 1/8" thick insulation and features primary and secondary drain connections
- Three-speed, 115/1/60 motor with quick-connect plug
- Draw-through design, easy slide-out blowers and quick connect plug
- Controls and motors are factory-wired and terminated in a junction box for single-point power supply
- One-inch duct collar on return- and supply-air openings
- Protective covers keep the grille openings free of debris during shipment and construction
- Individually tagged, crated and shipped as scheduled for installation
- ETL and AHRI certified; 100% factory tested
Options
Systems
- DX
- Chilled-Water
- Hot-Water
- Electric Resistance
- Steam
In any combination of the above
Insulation
- Thickness up to 1"
- Fiberglass
- Foil-face
- Elastomeric
Coil
- Copper fins/tubes
- Phenolic-coated
- Stainless-steel end plates
- Right left or top connections
- TXV - factory-mounted
- Freeze protection
- Custom fin spacing
Drain pan
- Stainless-steel
- Extended
- Drip tray
- Condensate float switch
- Condensate pumps
Cabinets
- Marine duty
- Extensions
- Pedestal base
- Front-return air grille
- Return-air grille
Electrical
- Motors
- 115, 208, 230 and 277
- Single or three phase
- 50 or 60Hz
- ECM
- Line or low voltage
- 1 to 8 kW electric resistance heat
- Disconnects
- Condensate float switch
- Condensate pumps
- Thermostats
- UV Light
- Controls
- Flow control
Accessories Options
- Valve package controls - wide selection of factory-mounted valves and controls
- Pedestal base
- Outside air openings
- Thermostats
- Condensate float switch
- Condensate pumps
- Pedestal base
• All sizes shown in inches.
• Right-hand unit shown, left-hand unit opposite.
• Coil connections determined by facing the supply-air opening.
• Electrical junction box is located on the same side as the coil connections.
• Unit must be installed level and condensate drain lines should be trapped.
• Drain pan is powder-coated epoxy with a 1/8” thick closed-cell insulation and has 3/4” NPT primary and secondary drain connections.
• Entire cabinet, scroll and blower wheel are heavy-gauge, galvanized steel.
• Coil Connections: 1/2” CW for CV006; 3/4” on CV008-022 chilled water. 1/2” HW on CV006-022 hot water.
• All sizes shown in inches.
• Right-hand unit shown, left-hand unit opposite.
• Coil connections determined by facing the supply-air opening.
• Electrical junction box is located on the same side as the coil connections.
• Unit must be installed level and condensate drain lines should be trapped.
• Drain pan is powder-coated epoxy with a 1/8” thick closed-cell insulation and has 3/4” NPT primary and secondary drain connections.
• Entire cabinet, scroll and blower wheel are heavy-gauge, galvanized steel.
• Coil Connections: 1/2” CW for CV006; 3/4” on CV008-022 chilled water. 1/2” HW on CV006-022 hot water.