Horizontal with Bottom
Return Air Plenum / LH-Q

200 - 1,200 CFM

The Horizontal with Bottom Return-Air Plenum (LH-Q) is a low-static (up to .25 ESP) fan coil that comes with a coil, blower/ motor assembly with quick-connect plug and a galvanized steel, powder-coated epoxy drain pan covered with ⅛-inch thick insulation. The galvanized steel plenum is insulated with ½-inch thick, over three pound density, neoprene-coated fiberglass. The plenum conceals the fan and motor assembly that is easily accessed for service by removing the back panel. This unit is easily mounted above ceilings, in closets, and in hallways.
  • Heavy gauge galvanized steel cabinet with neoprene coated 1/2" thick fiberglass insulation with 3.35 PCF density.
  • Coils are made of 1/2" OD copper tube with aluminum fins (12 FPI) equipped with manual air vent DX and steam coils do not include manual air vent. Coils are 100% underwater pressure tested at 350 PSI with a 300 PSI working pressure.
  • Galvanized drain pan is powder coated epoxy and subjected to a 650 hour salt spray test in accordance test in accordance with ASTM-B117. Also comes with 1/8" thick closed cell insulation and primary and secondary drain connections.
  • Three-speed, 115/1/60 PSC motor with quick connect plug.
  • One inch fiberglass, throwaway filter.
  • Units shall have published sound power level data tested in accordance with AHRI Standard 350-2000 (non-ducted equipment) and AHRI Standard 260- 2001 (ducted equipment)
  • One inch, reinforced duct collar on return and supply air openings.
  • Individually tagged, crated and shipped as scheduled for installation.
  • ETL approved, AHRI certified, 100% factory tested.
  • Drain Pans - stainless steel.
  • Insulation foil face, elastomeric and double wall separate foam insulation.
  • Coils - custom tubes, phenolic coated, stainless steel end plates. All options are available on one to six rows.
  • Three speed, 208-230/1/50-60 or 277/1/60 PSC motor with quick connect plug.
  • Systems - two or four pipe, hydronic cooling/heating, steam, direct expansion (DX) and/or electric heat. Steam heat. DX coating.
  • Electric Strip Heat from 0.5 to 5 kW.
  • ECM™ motors; programmed 3 speed, or variable volume, 120-240/1 /60 or 277 /1 /60.
  • Controls - wide selection of factory mounted valves and controls.
  • Filters - two inch thick throwaway, washable and pleated.
  • Flow control circulator for water heating custom applications.
  • Grilles available as double deflection and in custom colors.
  • Swing down, hinged solid grille/access door in custom colors.
  • Single or Double deflection supply air grille in custom colors.
  • Valve package controls - wide selection of factory-mounted valves and controls
  • Thermostats
  • Mixing Box
  • Manual
    • Motorized
    • Modulating
    • 3-Position Economizer

Customization

in any combination:

CONSTRUCTION

All unit chassis shall be fabricated of heavy gauge galvanized steel panels able to meet 125 hour salt spray test per ASTM B-117. All exterior panels shall be insulated with 1/2" thick, 3.35 pound per cubic foot, dual density fiberglass insulation rated for a maximum air velocity of 3600 f.p.m. Insulation shall conform to UL 181 for erosion and NFPA 90A and 90B for flame spread (25) and smoke developed (50) rating per ASTM E-84 and UL 723 and CAN./ULC, S102-M88.

All plenum units shall have a minimum 1" duct collar on the discharge and minimum 1" duct collar on the return.

OPTION: Provide foil faced insulation in lieu of standard. Foil insulation shall meet or exceed the requirements stated above, and in addition, meet ASTM Standards C665 and C-1136 for biological growth in insulation. Insulation shall be lined with aluminum foil, fiberglass scrim reinforcement, and 30 pound kraft paper laminated together with a flame resistant adhesive. All exposed edges shall be sealed to prevent any fibers from reaching the air stream.

OPTION: Provide elastomeric closed cell foam insulation in lieu of standard. Insulation shall conform to UL 181 for erosion and NFPA 90A for fire, smoke and melting, and comply with a 25/50 flame spread and smoke developed Index per ASTM E-84 or UL 723. Additionally, insulation shall comply with antimicrobial performance rating of zero, no observed growth, per ASTM G21. Polyethylene insulation is not acceptable.

OPTION: For exposed units, the bottom access panels shall be attached with quick open fasteners to allow for easy removal and access for service.

OPTION: For exposed units, provide double deflection discharge grille and either a rear return or bottom return single deflection grille. Supply and return duct connections are available. Unit mounting shall be by hanger and slotted hanging brackets provided at four locations. For easy installation, exposed units provided with 1/2" mounting knockouts in four places.

FAN ASSEMBLY

Unit fan shall be a dynamically balanced, forwardly curved, DWDI centrifugal type constructed of heavy gauge zinc coated galvanized steel for corrosion resistance. Motors shall be high efficiency, permanently lubricated sleeve bearing, permanent split capacitor type with UL and C-UL listed automatic reset thermal overload protection and three separate horsepower taps. Single speed motors are not acceptable.

The fan assembly shall be easily removable for servicing the motor and blower at or away from the unit. The entire fan assembly shall be able to come out of the unit by removing two wing nuts and unplugging the motor.

Plenum unit fan assemblies shall be easily serviced through an access panel provided.


OPTION: Devices used to energize and de-energize (switch) fan speeds must be totally silent. Mercury and/or quiet relays and/or contactors are not acceptable

COILS

All cooling and heating coils shall optimize rows and fins per inch to meet the specified capacity. Coils shall have seamless copper tubes and shall be mechanically expanded to provide an efficient, permanent bond between the tube and fin. Fins shall have high efficiency aluminum surface optimized for heat transfer, air pressure drop and carryover.

All coils shall be hydrostatically tested at 350 PSIG air pressure under water, and rated for a maximum of 300 PSIG working pressure at 200°F maximum water temperature. Direct expansion cooling coils shall include a fixed orifice distributor and nozzle.

Steam coils shall be standard steam type suitable for temperatures above 35°F and 15 PSIG maximum working pressure.


OPTION: Coil casing shall be fabricated from 304 stainless steel. All coils shall be provided with a manual air vent fitting to allow for coil venting.

OPTION: Provide automatic air vents in lieu of manual air vents. Cooling and heating coils shall be in the common coil casing, heating coils shall be furnished in the re-heat or pre-heat position on the unit with chilled water coils, and DX heating coil shall be in pre-heat position only.

ELECTRIC HEAT

Furnish an electric resistance heating assembly as an integral part of the fan coil unit, with the heating capacity, voltage and kilowatts scheduled. The heater assembly shall be designed and rated for installation on the fan coil unit without the use of duct extensions or transitions, and be located in the unit as to not expose the fan assembly to excessive leaving air temperatures that could affect motor performance.

The heater and unit assembly shall be listed for zero clearance and meet all NEC requirements, and be UL listed with the unit as an assembly in compliance with UL/ANSI Standard 1995.

All heating elements shall be open coil type Nichrome wire mounted in ceramic insulators and located in an insulated heavy gauge galvanized steel housing. All elements shall terminate in a machine staked stainless steel terminal secured with stainless steel hardware for corrosion resistance. The element support brackets shall be spaced no greater than 3-1/2” on center. All internal wiring shall be rated for 105°C minimum. All heaters shall include over temperature protection consisting of an automatic reset primary thermal limit and back up secondary thermal limit. All heaters shall be single stage. An incoming line power distribution block shall be provided and designated to accept single point power wiring capable of carrying 125% of the calculated load current.

OPTION: Devices used to energize and de-energize (switch) electric heat must be totally silent. Mercury and/or quiet relays and/or contactors are not acceptable.

FILTERS

All plenum units shall be furnished with a minimum 1" nominal glass fiber throwaway filter. Filters shall be tight fitting to prevent air bypass. Plenum unit filters shall be easily removable from the bottom or rear of the unit without the need for tools.

OPTION: Provide unit with 2" pleated filters rated at 25-30% efficiency and MERV 6 based on ASHRAE 52.2 - 1999 Electrical (Option) Units shall be furnished with single point power connection. Provide an electrical junction box with terminal strip for motor and other electrical terminations.

OPTION: The factory mounted terminal wiring strip consists of a multiple position screw terminal block to facilitate wiring terminations for the electric control valves and thermostats.

PIPING PACKAGES

Provide a factory assembled valve piping package to consist of a 2 or 3 way, on/off, motorized electric control valve and two ball isolation valves. Control valves are piped normally closed to the coil. Maximum entering water temperature on the control valve is 180°F, and maximum close-off pressure is 75 PSIG (1/2") or 50 PSIG (3/4"). Maximum operating pressure shall be 300 PSIG.

OPTION: Provide 3 wire floating point modulating control valve in lieu of standard 2 position control valve with factory assembled valve piping package.

OPTION: Provide either a fixed or adjustable flow control device for each piping package.

OPTION: Provide pressure temperature ports for each piping package. Piping packages are shipped installed on all units and can be shipped separately by request only.

DRAIN PANS

Primary condensate drain pans shall be single wall, heavy gauge, powder-coated epoxy subjected to a 650 hour salt spray test in accordance with ASTM B117, and shall extend under the entire cooling coil. Drain pans shall be of one piece construction and be positively sloped for condensate removal. Drain pans shall have primary and secondary drain connections.

The drain pan shall be externally insulated with a closed cell foam insulation. The insulation shall carry no more than a 25/50 Flame Spread and Smoke Developed Rating per ASTM E-84 and UL 723 and fungi resistant per ASTM G21/C1338, bacteria resistant per ASTM G22 and mold growth per UL 181.

OPTION: Provide a single wall primary drain pan constructed entirely of heavy gauge type 304 stainless steel for superior corrosion resistance. Stainless steel drain pans shall be externally insulated and meet or exceed the requirements stated above. Provide a secondary drain connection on the primary drain pan for condensate overflow.

OPTION: Provide a condensate overflow switch in the primary drain pan for condensate overflow.

Need Replacement Parts for Your Fan Coil Unit?

Fill out the form below

Similar Products

LH-B

More Info Horizontal Fan Coil
More...

The low profile and flexible design of the Horizontal Basic fan coil (LH-B/low static and B/high static) is ideal for multiple applications. The slim, compact design is well suited for drop-ceiling, closet, hallway and other concealed applications. The Horizontal Basic comes with a powder coated epoxy drain pan and a wide range of coil, motor and controls options. These models have no exterior cabinet

LH-R

More Info Horizontal Fan Coil
More...

The Horizontal with Return Air Plenum (LH-R/low static and R/high static) is our basic model with a galvanized rear return air plenum. Ideal for mounting above ceilings, in closets, hallways and bathroom areas, the plenum conceals the unit’s blower motor which is easily accessible for service by removing the bottom panel. Available as a rear return or bottom return comes with filter.

LH-D

More Info Horizontal Fan Coil
More...

The Horizontal Deluxe fan coil (LH-D/low static and D/high static) is designed for horizontal exposed ceiling mounted applications. The Horizontal Deluxe is our basic unit housed in a cabinet intended for “free blow” exposed ceiling mounting. Ideal for remodel situations where adding AC ductwork is limited. Deluxe cabinets are constructed of cold rolled steel and finished with 385˚ baked on tough, soft white epoxy powder coated finish.

LH-F

More Info Horizontal Fan Coil
More...

The Horizontal Flush (LH-F/low static and F/high static) is a recessed fan coil designed for flush ceiling applications. This unit is designed to accommodate ducted supply air. The telescoping frame and hinged access panel of the Horizontal Flush give it the flexibility to accommodate any type of ceiling. same attractive, durable powder coated cabinet as the Horizontal Deluxe.

LH-E

More Info Horizontal Fan Coil
More...

The Horizontal Flush Bottom Supply and Return (LH-E/low static and E/high static) is a recessed fan coil designed for flush ceiling applications. The telescoping frame and hinged access panel of the Horizontal Flush Bottom Supply and Return allow it to fit any type of ceiling. The unit comes in the same attractive, durable powder coated cabinet as the Horizontal Deluxe.

LH-Q

More Info Horizontal Fan Coil
More...

The Low-Static Horizontal Ceiling-Recessed with Bottom Return-Air Plenum (LH-Q) is a low-static (up to .25 ESP) fan coil that comes with a coil, blower/ motor assembly with quick-connect plug and a galvanized steel, powder-coated epoxy drain pan covered with ⅛-inch thick insulation. The galvanized steel plenum is insulated with ½-inch thick, over three pound density, neoprene-coated fiberglass. The plenum conceals the fan and motor assembly that is easily accessed for service by removing the back panel. This unit is easily mounted above ceilings, in closets, and in hallways.

LHP

More Info Horizontal Fan Coil
More...

This basic low-static with ultra low profile horizontal (LH-X) is ideal for multiple applications. It’s slim, compact design is well suited for drop ceiling, closet, hallway and other concealed applications where our horizontal basic (LH-B) dimensions are not adequate. The LPH Series fan coils come with a powder coated epoxy drain pan with a wide range of coil, motor and controls options.

The LP-X horizontal fan coil with return air plenum (LH-Y) is our basic LH-X with a galvanized rear return
air plenum, ideal for mounting above ceilings, in closets, hallways and bathroom areas, the plenum conceals the unit’s blower motor which is easily accessible for service by removing the bottom panel. Rear air plenum units come with filter.

WARNING: This product can expose you to chemicals including epichlorohydrin which is known to the State of California to cause cancer and birth defects and/or other reproductive harm. For more information go to www.p65warnings.ca.gov

TOP